Hettich Universal 30 Rf Manual10/11/2021
ROTANTA 460 RF.8K delivers true-to-life picture quality Q900R Key Features Real 8K Resolution: With exceptional depth of detail, our real 8K resolution¹ will draw you in to the picture. RCF of 21,382 with up to 30 tubes, enabling rapid processing of. KG AR1401EN Repair instructions UNIVERSAL 320 UNIVERSAL 320 RSMALL SMALL CENTRIFUGES MANUAL CENTRIFUGE / EBA 200 / 200 S. This highly robust pump can run at pressures of up to 500 psi.06.08 Andreas Hettich GmbH & Co. Clean-in-Place (CIP) capable with optional flat body profile and free draining vertical ports. The Waukesha Universal 2 Series positive displacement pumps include advanced sanitation technologies, long life features and installation flexibility.Abbott 3531 Centrifuge - Ozark Biomedical. KG All.Centrifuges - Grainger Industrial Supply. KG Föhrenstraße 12, D-78532 Tuttlingen / Germany Phone (07461) 705-0 Fax (07461) 705-125 , © 2005 by Andreas Hettich GmbH & Co. 2/66 Andreas Hettich GmbH & Co. Quantum Processor 8K: Our most powerful processor delivers the ultimate picture, sound and smart experience.
![]() Hettich Universal 30 Rf Free Draining Vertical15/66 ROTORCODE 10.3 Error Error during reading the rotor code. Admissible mains voltage see chapter "Technical specification". Mains voltage is too low. Check the maximum permissible imbalance values i.14/66 CONTROL - ERROR 6 Error Lid lock error Error consequence No further user operation is possible. Weight difference in rotor components. Cause of error 17/66 ☌ / * -ERROR 51 Error Overtemperature on condenser Error consequence The rotor slows down braked until it stops. No further user operation is possible. Error consequence The rotor slows down braked until it stops. Error co.16/66 CONTROL – ERROR 21 Error Faulty speed measurement. Electronics U320 (A1) is defective. Magnetic code on the rotor is defective. Undervoltage in intermediate circuit. Cause of error / measurements 19/66 FU / CCI - ERROR 62 Error Frequency converter - error. No further user operation is possible. Error consequence The rotor slows down braked until it stops. Cause of error / measurements 18/66 ☌ / * -ERROR 55 Error The measured temperature on the condenser is out of range. Overtemperature switch opens because o.21/66 FU / CCI - ERROR 84 Error Frequency converter recognises excess speed. Cause of error / measurements No further user operation is possible. Error consequence The rotor slows down braked until it stops. Cause of error 20/66 FU / CCI - ERROR 67 Error Overtemperature in the motor. No further user operation is possible. Upon the appearance of a disturbance in 2 second intervals. 6.1 Summary of the possible settings and interrogations.24/66 6.2 Acoustic signal The acoustic signal sounds: The corresponding menus are selected by pressing keys or combinations of keys. Cause of error 23/66 6 Settings and interrogations All settings and interrogations are performed via the keyboard. No further user operation is possible. The error will be activated when the speed exceeds the following limit value: maximum sp.22/66 SENSOR – ERROR 93 Error The temperature of the imbalance sensor is out of range Error consequence The rotor slows down braked until it stops. It is at any time possible to terminate the procedure by pressing the STOP / OPEN key twice. 26/66 6.4 Blank the machine type in the display The display of the machine type after switching on the unit can be blanked. It is at any time possible to terminate the procedure by pressing the STOP / OPEN key. The acoustic signal is stopped.25/66 6.3 Operating hours The inquiry and the change of the operating hours is only possible if the rotor is at standstill. In order to be able to check the function of the speed sensors the lid must be opened before the starting the function test. This automatic repetition remains activa.28/66 6.6 Function test The individual components of the centrifuge can be tested on its function. The break time between the centrifugation runs can be set. Press the SELECT key → SOUND / BELL OFF Turn the control knob one step to the right → ERROR LED ON The yellow error LED lights up 17. Turn the rotor by hand → Speed RPM XXX Speeds ≥100 RPM will be displayed 10. Press the SELECT key → Speed RPM 0 Function test of the speed sensor (B4) on top of the motor It is at any time possible to terminate the. The inquiry of the operating hours is only possible if the rotor is at standstill. Turn the control knob one step to the right → ADC 7 = 4956 mV Lid lock, right lid switch (A3 / S1): Switch actuated (lid closed) 4900 mV 20.32/66 6.7 Logging the occurred faults The data of the two last occurred faults are stored and can be queried. ![]() The imbalance switch-off is specified by the indication of the difference in weight of opposite rotor posit. Turn the control knob to the right → → IMBALCHG XX Internal operating hour of the last change of the imbalance switch-off OffsetCHG XX Internal operating hour of the last offset compe.37/66 6.11 Imbalance values 6.11.1 Setting the imbalance switch-off A change of the imbalance switch-off affects all rotors.
0 Comments
Leave a Reply.AuthorMike ArchivesCategories |